Difference between revisions of "Power Monitor"
| (5 intermediate revisions by the same user not shown) | |||
| Line 21: | Line 21: | ||
[[File:LTC2945reference.png|400px]] | [[File:LTC2945reference.png|400px]] | ||
| − | Note: this board grounds both I2C address pins, so the address is | + | Note: this board grounds both I2C address pins, so the address is B1101111 |
Several options are available to connect this board into the project that's being measured: | Several options are available to connect this board into the project that's being measured: | ||
| Line 27: | Line 27: | ||
* Terminal Block - the gerber silkscreen doesn't show this well, but near the bottom of the board, a terminal block can be mounted, then connect the (+) terminal (on the left) to the positive terminal, then the (-) terminal (on the right) to the project. | * Terminal Block - the gerber silkscreen doesn't show this well, but near the bottom of the board, a terminal block can be mounted, then connect the (+) terminal (on the left) to the positive terminal, then the (-) terminal (on the right) to the project. | ||
* Direct solder - instead of using the terminal block, wires can be soldered to these through-holes to be used as 'leads'. | * Direct solder - instead of using the terminal block, wires can be soldered to these through-holes to be used as 'leads'. | ||
| + | |||
| + | [[File:PowMonPicture.JPG|400px]] | ||
== Schematic == | == Schematic == | ||
| Line 36: | Line 38: | ||
== Parts == | == Parts == | ||
| + | [http://www.kevindarrah.com/wp-content/uploads/2017/04/PowMonitorV1.xlsx Parts List HERE] can be uploaded right into [https://www.digikey.com Digikey] NOTE: I have not tested the form/fit of the terminal block on this BOM, so please let me know if any issues | ||
== Assembly == | == Assembly == | ||
| + | |||
| + | {{#evt: | ||
| + | service=youtube | ||
| + | |id=https://www.youtube.com/watch?v=aw75rmYgjxc | ||
| + | |dimensions=560x315 | ||
| + | }} | ||
== Tutorial == | == Tutorial == | ||
| + | |||
| + | {{#evt: | ||
| + | service=youtube | ||
| + | |id=https://www.youtube.com/watch?v=PVj4k0R9s4E | ||
| + | |dimensions=560x315 | ||
| + | }} | ||
| + | Resources: | ||
| + | [http://kevindarrah.com/download/arduino_code/LTC2945.ino The Code] | ||
Latest revision as of 07:35, 19 April 2017
...Back to Projects:
Contents
The Power Monitor Board
Introduction
Based on the LTC2945, this board can measure Voltage, Current, and Power. Communication to the board to read out the values (among many other parameters) is done over a simple I2C interface. It uses a sense resistor to measure the current with varying degrees of resolution based on the value. The board has been designed to allow changeable sense resistors:
- 10 ohm = 10mA Max Current with 2.5uA Resolution
- 1ohm = 100mA Max Current with 25uA Resolution
- 0.1 ohm = 1A Max Current with 250uA Resolution
- 0.01 ohm = 10A Max Current with 2.5mA Resolution (ACTUALLY 5A MAX!) Though you 'could' measure 10A, that would burn up the 0.25W current sense resistor. If you need to measure higher than 5A, then you might be able to get a 0.01ohm resistor with a higher power rating.
Each of these resistors can be soldered onto a mini Current Sense Board, then based on the expected max current of the project, the appropriate Current Sense Board can be plugged into the Power Monitor Board.
Other features include min/max logging of the values, programmable alarm thresholds with dedicated alarm output(ALE), and an auxiliary 2.048V Analog Input (ADI).
Though, the board shows 3V3, the board is also compatible with 5V systems. This configuration from the datasheet was implemented:
Note: this board grounds both I2C address pins, so the address is B1101111
Several options are available to connect this board into the project that's being measured:
- The headers - the 9 pin header on the left with ++++ and ---- connect in line with the positive supply to the project. x4 pins each are given to allow for higher currents. For example, connect the ++++ pins to the positive terminal of the power supply, then the ---- pins to the project.
- Terminal Block - the gerber silkscreen doesn't show this well, but near the bottom of the board, a terminal block can be mounted, then connect the (+) terminal (on the left) to the positive terminal, then the (-) terminal (on the right) to the project.
- Direct solder - instead of using the terminal block, wires can be soldered to these through-holes to be used as 'leads'.
Schematic
Purchase
Coming soon - given to Patrons ...
Parts
Parts List HERE can be uploaded right into Digikey NOTE: I have not tested the form/fit of the terminal block on this BOM, so please let me know if any issues
Assembly
Tutorial
Resources: The Code
